Product ID: HP-25, HP-100

    Differential Probe 25MHz/ 100MHz

    25 MHz Differential Probe Model  HP-25
    • Make floating measurements simply and safety
    • Compatible with analog or digital storage oscilloscope
    • In compliance with IEC-1010.1, IEC-1010.2-031
    CAT III , Pollution  degree 2


         HP-25 Specifications:

         25 MHz HP-025 Differential Probe
    Bandwidth : DC to 25MHz (-3dB)
    Attenuation Ratio : 1/20 & 1/200
    Accuracy : +2%
    Input Impedance : 4M Ohm / 10pF each side to ground
    Differential Input Range : +1400V(DC+AC peak) or 1000V rms for 1/200
    +140V(DC+AC peak) or 100V rms for 1/200
    Common Mode Range : +1400V(DC+AC peak) or 1000V rms
    Output Offset : <+5mV, -10  deg C to 40 deg C
    Cable length : 95cm (RG58/U)
    Power Requirements : 4x AA cels or 6VDC/60mA mains adapter (not supplied)
    Dimension : 6.6" x 2.4" x 0.8" (168x62x20mm)
    Weight : 285gms (0.583 lbs)








         HP-100 Differential Probe
    • Bandwidth DC to 100MHz (-3dB)
    • Input Impedance 4M£[//7pF Accuracy +/- 2%
    • Attenuation Ratio 1/100& 1/1000
    • Input Voltage : +/- 140V(DC+Peak AC) or 100Vrms for 1/100
























    Bandwidth DC to 100MHz (-3dB)
    Attenuation 1:100/1000
    Accuracy +/- 2%
    Rise Time 3.5ns
    Input Impedance 4Mohm//7pF each side to ground
    Input Voltage
    -Max. Differential* ±140V(DC + Peak AC) @ 1/100
    ±1400V (DC + Peak AC) @ 1/1000
    - Common Mode Range* ±1400V (DC + Peak AC) @ 1/100 & 1/1000
    - Absolute Max. Voltage*
    (Differential or Common Mode) ±1400V (DC + Peak AC) @ 1/100 & 1/1000
    Output Voltage
    - Swing (into 50kohm load) ±1.4V
    -Offset (typical) <+/-5mV
    -Noise (typical) 0.6mVrms
    -Source Impedance (typical) 50 ohm
    CMRR (typical) -80dB@60Hz; -50db@1MHz
    Ambient Operating Temperature -10 to 40 degree centigrade
    Ambient Storage Temperature -30 to 70 degree centigrade
    Ambient Operating Humidity 25 to 85% RH
    Ambient Storage Humidity 25 to 85% RH
    Power Requirements
    -Standard 4xAA cells or 6VDC/200mA mains adaptor**
    or regualted 9VDC/120mA mains adaptor  

    Weight 500gms
    Dimension (LxWxH) 207mmx83mmx38mm

    * Voltage limit is the lesser of the DC+Peak AC and RMS values..
    ** a. The supplied voltage must be less than 12V and greater than 4.4V, otherwise the probe could
    be damaged or can't be operated properly.
    　b. polarity is “+” inside and “–” outside. For wrong polarity, built-in circuit protects the probe, no
    danger or damage will occur.
    　c. When the voltage of the cells become too low, the power indicator on the panel will flicker.




         Ordering information:


    25MHz Differential Probe  Model: HP-25
    100MHz Differential Probes Model: HP-100


    Minimum Order: Negotiable
    TEL: 886-2-27375866
    FAX: 886-2-27373343
         E-mail:  sales@tecpel.net
         http://www.tecpel.net
    TECPEL CO., LTD.
    Differential  Probe
    Model: HP-25
    Share by: